Motion Labs 19 Pin Overmolded Multicable 12/14 AWM, 25ft

PRODUCT DESCRIPTION

19 Pin, VSC Compatible
Phase 3 Connectors
10-Year Connector Warranty
6 Circuits
12/14 AWM
600V / 90°C
Overmolded Connectors
Bonded Ground Ring
25 ft
14 lb

In short: The Motion Labs 19 Pin Overmolded Multicable is a 6-circuit lighting multicable on 12/14 AWM cable rated 600V and 90°C. Both ends have Phase 3 brand VSC compatible 19 pin circular connectors, the multipin format many crews call Socapex or Soca, backed by a 10-year warranty from Phase 3. The connectors have aluminium bodies and a bonded ground ring on pins 13 to 18. A rubberised overmold replaces the metal backshell for stronger strain relief. This 25 ft length (part number 1410-02-33-04-003) weighs 14 lb and has 6 in of clear heat shrink on each end for labels.

Why overmolded

Why choose an overmolded 19 pin multicable?

On a standard mechanical 19 pin connector, every pull, flex and twist works on the terminations. Over time the conductors get stressed, the insert can loosen and spin, and you end up with pushed-back pins and hot spots. Motion Labs overmolds the connector and cable into one piece, which takes that stress off the pins.

Phase 3 connectors, 10-year warranty

Motion Labs uses Phase 3 brand 19 pin connectors, backed by a 10-year warranty. They are VSC compatible, UL/CSA certified and have aluminium bodies with crimp or solder termination.

Overmolded strain relief

A rubberised overmold replaces the metal backshell and resists pull, flex and twist, holding the connector and cable together as one piece.

No torsion at the pins

Overmolding removes torsion between the cable and connector, which Motion Labs says reduces the risk of burnt or pushed-back pins, shorts and hot spots.

Two-step molding

An injected polymer first encapsulates the conductors and pins or sockets. A rubberised outer layer is then molded over the whole assembly.

Bonded ground ring

The ground pins, 13 to 18, are bonded together at the connector with a ground ring.

Ready to label

6 in of clear heat shrink on each end gives you a protected spot for cable labels and inventory tags.

On set & on show

Where is 19 pin multicable used?

One 19 pin multicable carries six circuits, replacing six separate cables. Lighting and production crews and rental houses use it for:

Truss and pipe power, from dimmers or distro to breakouts at the fixtures
Feeding stringer boxes such as the Motion Labs 19 pin to Edison stringer box
Film and TV sets, running six circuits from distro to a lighting position in one cable
Concert and touring rigs that need fast, repeatable power runs every load-in
Theatre and venue installs moving circuits from the dimmer room to the stage
Rental house inventory, where overmolded ends hold up longer between repairs

Using it well

How do you run and maintain a 19 pin multicable?

Plan the circuits. Each of the six circuits needs breaker protection that suits 12 AWG conductors, your distro and your local code.
Test before the job. Check continuity and pin-out on every run. Motion Labs makes the CT-004 touchscreen cable tester for 19 pin cables.
Label both ends. Put your labels under the 6 in clear heat shrink on each end so they stay readable.
Support the weight. At 14 lb for 25 ft, tie off vertical runs and don't let the cable hang from the connectors.
Connect with power off. Mate and unmate multipin connectors with the circuits de-energized.

The connectors are UL/CSA certified, but the 12/14 AWM cable is not UL listed. Check that it meets your venue's and jurisdiction's requirements before use.

Full specifications

Motion Labs 19 Pin Overmolded Multicable specifications

Technical information
Part number (25 ft)	1410-02-33-04-003
Manufacturer	Motion Labs
Connectors	Phase 3 brand 19 pin circular, VSC compatible, aluminium body, crimp or solder termination
Connector warranty	10 years (Phase 3)
Circuits	6
Cable	12/14 AWM, 600V, 90°C
Ground ring	Pins 13 to 18, bonded
Strain relief	Overmolded (rubberised outer layer over injected polymer)
Labelling	6 in clear heat shrink on each end
Length	25 ft
Weight	14 lb
Certifications	UL/CSA connectors. Cable is not UL listed.

Lengths

What lengths does the Motion Labs 19 pin multicable come in?

Motion Labs makes this overmolded multicable in six lengths.

Motion Labs 19 Pin Overmolded Multicable, 12/14 AWM
Part number	Length	Weight
1410-02-33-04-003	25 ft	14 lb
1410-02-33-03-003	50 ft	28 lb
1410-02-33-02-003	75 ft	40 lb
1410-02-33-01-003	100 ft	56 lb
1410-02-33-08-003	125 ft	70 lb
1410-02-33-09-003	150 ft	84 lb

Questions

Motion Labs 19 pin multicable frequently asked questions

What is the Motion Labs 19 Pin Overmolded Multicable?

It is a 6-circuit lighting multicable on 12/14 AWM cable rated 600V and 90°C, with Phase 3 brand VSC compatible 19 pin circular connectors on both ends. The connectors have aluminium bodies, a bonded ground ring on pins 13 to 18 and an overmolded rubberised strain relief. The 25 ft length weighs 14 lb.

What connectors does the Motion Labs multicable use?

It uses Phase 3 brand 19 pin circular connectors, backed by a 10-year warranty from Phase 3. They are VSC compatible and UL/CSA certified, with aluminium bodies and crimp or solder termination.

What does 12/14 AWM mean?

12/14 means 12 AWG conductors with 14 conductors in the cable. AWM stands for Appliance Wiring Material, a UL cable category. This cable is rated 600V and 90°C.

Is a 19 pin multicable the same as Socapex?

Socapex is a brand name that many crews use for the 19 pin multipin connector format, often shortened to Soca. The Motion Labs multicable uses VSC compatible 19 pin circular connectors in this format.

How many circuits does a 19 pin multicable carry?

A 19 pin multicable carries six circuits. In common wiring, pins 1 to 6 are hots, pins 7 to 12 are neutrals and pins 13 to 18 are grounds. On this cable, ground pins 13 to 18 are bonded together with a ground ring.

Is the Motion Labs 19 pin multicable UL listed?

The 19 pin connectors are UL/CSA certified, but the 12/14 AWM cable is not UL listed. Check that it meets your venue's and jurisdiction's requirements before use.

Why is an overmolded connector better than a metal backshell?

On a mechanical connector, conductors can get stressed at the terminations and the insert can loosen and spin. Overmolding locks the cable and connector together, which Motion Labs says improves shock absorption, pull strength and flex relief and reduces the risk of burnt or pushed-back pins, shorts and hot spots.

What lengths are available?

Motion Labs makes it in 25, 50, 75, 100, 125 and 150 ft lengths, weighing from 14 lb for 25 ft to 84 lb for 150 ft. The 25 ft length weighs 14 lb.

How do I test a 19 pin multicable?

Test continuity and pin-out before each job. Motion Labs makes the CT-004 touchscreen cable tester for checking 19 pin cables.

Power distro advice from people who actually run cable

Barn Door Lighting Outfitters has supplied film lighting, grip and power distribution since 1995. We're still a small, family-owned shop in Beaufort, South Carolina. Not sure which multicable length, breakout or stringer box your rig needs? Call 888-276-3667 or email info@barndoorlighting.com and a real person will help you spec it.